IPMIT304 / IPMIT354 - Quick Start Guide
|
•The connections to the must be clean and dry, and not exposed to moisture or excessive dust. •Do not touch the any of its connections with wet hands. •Ensure the power is switched off to the IPmitter if not in use for a long period of time. •There are no user serviceable parts in the IPmitter and opening or attempting to repair the product will void the warranty. •Only use a 12V DC Regulated PSU (at least 500mA) or a 48V PoE Supply (also known as 802.3af). •Do not install or use the device if the power cable or network connection is damaged. |
www.systemq.com/pdf/manual/xIPMIT304.pdf
|
The IPmitters can be used to "bridge" an IP connection for IP cameras or other IP devices wireless between two points, devices connect via the RJ45 port on the IPmitter.
Powering
Option 1 - Power from 12V DC (via the 2.1mm DC Socket), the current consumption is 300mA.
The IPMIT304 is polarity sensitive so connections must be made correctly.
Option 2 - Power the IPmitter using 48V PoE, in the RJ45 WAN/POE Socket.
The IPMIT304 will take approximately 1 minute to boot up.
Note the IPmitter does NOT provide PoE power out to a PoE camera or load device.
|
1 = Function Button |
2 = LED Display |
|
3 = Setting |
|
4 = 12V DC. 2.1mm DC Socket |
|
5 = Connection LEDs |
|
6 = WAN - 10Mbs / 100Mbs 48 PoE network socket |
|
7 = LAN - 10Mbs / 100Mbs network socket |
|
8 = Reset/Pair Button |
Standard WiFi Bridge Setup
For more setup options see the full manual
Available Channels – Available channels 34-64, 100-140 (In multiples of 4)
The IPmitters are sent out as default on H (Host), and need pairing up before installing. One IPmitter needs to be set to H (Host) and the other to C (Client), they both have to be set to the same channel number.
NOTE : - Keep both IPmitters at least 2m apart during pairing, if the IPmitters are too close they will "de-sense" and not pair.
- Do not attempt to pair both IPmitters connected to the same PoE switch, they will detect a network loop and not pair.
Example - Pairing
1. Press the F (function) button and "H" will flash. Press the S (setting) button to change to "C"
2. Press the F button 4 times to move across the display, then the whole display will flash for about 5 seconds to indicate the settings have been saved.
3. Now press the RST (reset) button for 1 second on both IPmitters. The display will change to a P with a rotating segment whilst pairing and will show P and a value once paired. Pairing can take up to 2 minutes.
The strength will range P-01 (Good) to P-75 (Poor). If P-95 shows then the IPmitters have not paired.
To add more clients (up to 4) to one host then set the channel on the new client and press the reset buttons on the new client and the Host.
|
www.zipdvr.com/howto/TIP459-How-To-Add-IP-Cameras.html
If using the IPMIT304 with a ZIP Recorder then the cameras needs to be manually configured, scan the QR code to the left for the "how to guide" |
LAN Port 1 Speed |
10Mbs / 100Mbs |
LAN Port 2 Speed |
10Mbs / 100Mbs |
Frequency |
5.8Ghz |
Wireless Data Speed |
450Mbps |
Wireless Standard |
IEEE802.11AC/A |
PoE Voltage |
48V |
12V Input Option |
Yes |
Max Tx Distance |
700m (Recommend 350m) |
Easy Pair Technology |
Yes |
Support 1 - 1 |
Yes |
Support 1 - Many |
Yes |
Modes |
Access Point / Repeater |
Mounting |
Wall Or Pole (Not Supplied) |
Dimensions |
165 x 88 x 56mm |